|Material:||PVC Decoration Profile||Color:||Customized|
|Surface:||Hot Stamp||Molding Method:||Extrusion|
plastic decorative mouldings,
pvc decorative mouldings
Hot Stamping Pvc U Joint PVC Extrusion Profiles Easy Maintenance / Install Customized
PVC Extrusion Profiles Detailed Description
PVC U joint, accessories for installing pvc wall and ceiling panel
Hot stamping surface, color can be same as pvc panel
5mm to 10mm thickness
Usually be 40pcs/bag
Match the quantity of pvc panel
Within 15-20 days after receiving deposit
PVC Extrusion Profiles Features
1. Fire proof, rot proof , damp proof and rust proof
2. Water proof and heat proof
3. Easy maintenance
4. Impact Resistant
5. Light in weight and easy to install can save a lot of time and man power cost.
6. Easy to cut, drilled, nailed and sawed. PVC Wall Ceiling Panel
PVC Panel Installation
1. PVC Panels may be nailed, stapled or screwed through the panel edge groove base flap into plumb
and level wooden battens, or bonded direct to flat, plumb, sound and smooth walls or ceilings. If the
installation sub surface is uneven install an appropriate timber batten frame system to the wall or
ceiling to ensure a level batten frame to apply the panels to.
2. Installation of PVC panels should commence by attaching a scotia trim or end U Joint as required
to the wall, and or, ceiling edge joint.
3. Mechanically fix or adhere the end cap/starting profile to the wall. For wet area applications apply
a full length unbroken bead of silicone sealant into the channel of the starting profile.
4. If gluing panels to the wall, ceiling or framework, apply multiple full length beads of panel adhesive
to the back of the panel and angle it into the starting profile. Alternatively if a wooden frame sub
system is installed and nailing installation is to be used, locate the panel in position and staple or pin
through the groove base flap into the wooden framing. For wet area applications apply a small
silicone bead along the upper tongue face of the next panel. Locate the next panel tongue into the
groove of the previously installed panel and fix in the same manner as the first panel. Remove any
excess silicone once the profiles are located.
5. Continue across the sub surface or frame, using the same techniques per panel or H type trim
mid-joints can be used if required. In some cases it may be necessary to cut off the tongues or
grooves before fitting into any profiles used.
6. Use an internal or external corner trim at wall corners or returns.
7. Finish the installation of the panels by measuring and cutting the last panel to size. Finish and seal,
(for wet area use) the final edge using silicone sealant, and either an end U cap or scotia trim to the
panel edge as required, prior to fixing to the final panel and end trim as one unit to the sub surface.
8. Ensure all panel ends and edges around sinks, baths, shower trays, shower units and any pipes or cut
outs are fully sealed using silicone sealant. The PVC panel warranty will be void and no product fault
claims will be accepted, where a problem occurs due to incorrect or inappropriate sealing of joints or
seal failure as a result an inappropriate sealant being used.
9. When fixing any accessories or heavy items to the panel surface ensure that the screws used to
fix the item locate securely into the wall or battens as PVC panels are a thin cellular product and
therefore the PVC material itself has limited holding capacity. Do not over tighten screws / accessory
base plates or compression damage to the panel surface may occur.
|Name||PVC Co-extrusion Profile|
|Material||Virginal PVC Granules|
· Make the production by your own drawings.
· These production are mainly customized by the customer,like length,color,surface and so on.
· These production could instead of some metal section ,and be used for some structure or decoration parts.
· Mainly used as the decoration profile,could instead of metal appearance profile.
· It looks like painted or coated,but it doesn't.
· It is made of co-extrusion,its surface hardness is much better than painting or coating.
Features of Plastic production:
1. Lifetime No Rot Warranty
2. Will not crack, split or warp
3. No Insect Damage and Ready to Install
4. Factory Applied Readi-Finish
5. Low Maintenance
6. Moisture & Termite Proof Material
7. High Energy Efficiency• Repaint able with Oil or Latex Paint
8. Does Not Promote Mold or Mildew
9. Installs with standard wood working equipment
The Overview of Tongxiang Hengchao Plastic Co.,Ltd
Glimpse of Tongxiang Hengchao Corner